Welcome, Guest
Username: Password: Remember me
Forgot your password? Forgot your username? Create an account

TOPIC: IO guide question

Re:IO guide question 13 years 3 months ago #1434

  • Snarf77
  • Snarf77's Avatar
  • OFFLINE
  • Platinum Boarder
  • Posts: 847
  • Thank you received: 2
  • Karma: 5
Thanks a lot Claes,

download in progress....

Other question:
Did you test the analog pwm output in the Arduino module. I need some AO and plan to buy some electronic component to convert pwm (0-5V) to analog (0-10V) but I don't see anything about how to pilot those output in the IO guide new release. Is there a problem with that or it is just not tested yet ??

Congrulations again for you hard work...

Snarf
The administrator has disabled public write access.

Re:IO guide question 13 years 3 months ago #1443

  • claes
  • claes's Avatar
  • OFFLINE
  • Platinum Boarder
  • Posts: 3179
  • Thank you received: 502
  • Karma: 133
Hi Snarf,

I was a bit lazy skipped the pwm's. Didn't think anyone would miss them...
But it should be quite easy to add them. I'll have a look at it.

/Claes
The administrator has disabled public write access.

Re:IO guide question 13 years 3 months ago #1453

  • Snarf77
  • Snarf77's Avatar
  • OFFLINE
  • Platinum Boarder
  • Posts: 847
  • Thank you received: 2
  • Karma: 5
It could sometime be very useful to have some analog outputs (display, sending reference to other system...). The conversion from pwm to 0-10V is described on many electronic forum so (personally) I plan to use them. I don't know if I'm the only one in this case...

Regards

Snarf
The administrator has disabled public write access.

Re:IO guide question 13 years 3 months ago #1462

  • claes
  • claes's Avatar
  • OFFLINE
  • Platinum Boarder
  • Posts: 3179
  • Thank you received: 502
  • Karma: 133
Hi Snarf,

New version with support for PWM outputs

[url]files/tmp/pwr48_4.8.1-0.4ubuntu_amd64.deb[/url]

Install and activate 'Functions/Update Classes' in configurator menu of your root volume.
Note that there is a new version fo the arduino sketch that has to be downloaded to the board.

/Claes

Post edited by: claes, at: 2011/01/20 10:07
The administrator has disabled public write access.

Re:IO guide question 13 years 3 months ago #1463

  • marc
  • marc's Avatar
  • OFFLINE
  • Platinum Boarder
  • Posts: 710
  • Thank you received: 70
  • Karma: 24
Hi Claes,

In the next v4.8.1 is the complete Arduino (Analog I/O and Digital I/O) going to be implemented just like the K8055? If yes....., then I will be very pleased and will wait because I run 32 bit...... The Arduino Duemilanove is running like a charm with Digital I/O.....

Regards,
/Marc
Please, use the Wiki if you succeeded your project or solved your problem. Share your work, so we can learn from each other.
The administrator has disabled public write access.

Re:IO guide question 13 years 3 months ago #1472

  • Snarf77
  • Snarf77's Avatar
  • OFFLINE
  • Platinum Boarder
  • Posts: 847
  • Thank you received: 2
  • Karma: 5
Hi Claes,

Stupid question (I'm used to):
- You spoke about a new sketch for Arduino to load but where is it located ? it is part of the .deb you provide ?

Concerning the Arduino environment I have problem to install it (perhaps x64 pb ?). Which version did you use (0022 ?). The linux version seems to be only for i386 ? did you recompile it ? I never did that so I'm a little lost...

Sorry in advance

Snarf

Post edited by: Snarf77, at: 2011/01/21 18:59
The administrator has disabled public write access.
Time to create page: 7.835 seconds